Variable-frequency drives (VFD) V & Hz measurement.
LoZ voltage measurement to drain ghost voltages.
Check 3Φ phase sequence.
Motor Inrush current measurement.
True RMS reading on AC and DC+AC mode. (3901)

Capacitance measurement 1000µF
Variable-frequency drive (VFD) V & Hz measurement.
Lo-Z voltage measurement to drain ghost voltages.
Check 3Φ phase sequence.
True RMS reading on AC and DC+AC mode.
Inrush current measurement.
A measurement for HVAC flame sensors.
mV measurement range to interface with other accessories.
Crest Factor & Harmonic ratio measurement.
Data hold, Auto hold & Peak hold mode.
Max/Min/Avg record mode.
Data memory & read function.

EN61010-1
600V INSTALLATION VAT III
POLLUTION DEGREE2

Auto-Ranging Frequency measurements
Auto ZERO mode
Data Hold mode
PEAK Hold mode
True RMS Reading

Accurate DC/AC digital clamp meter for current measurement.
1200A AC/DC current measurement
Analog Output for datalogger or oscilloscope.
One touch zero for DCA adjustment.
23mm diameter jaw.
Integrated current probe for waveform observation or recording
Large 3 3/4 digits LCD
Fast bargraph display (30 times/sec.) for transient observation.
Max/Min and Data Hold functions.
Easy single rotary switch for any function selection.
Ideal for works in crowded switch box or cable areas.

AC+DC power measurement: 0 ~ 240KW
AC current: 0 ~ 400A (True RMS)
DC current: 0 ~ 400A
AC voltage: 0 ~ 600V (True RMS)
DC voltage: 0 ~ 400V
Frequency measurement (Auto range): 1 ~ 100K Hz

3-3/4 Digital LCD with bar-graph.
Auto-Ranging on Volt, Ohm, Current,
Frequency measurements.
Auto-power off.
Data Hold mode.
MAX/MIN Hold mode.
Zero Adjustment/Relative Reading.
PEAK Hold mode. （only ACV and ACA Range）

3-3/4 Digital LCD with bar-graph
Auto-Ranging on Volt, Ohm, Current, Frequency measurements
Auto-power off
Data Hold mode
MAX/MIN Hold mode
Zero Adjustment/Relative Reading

Category: CAT II 1000V , CAT III 600V
ACA: 20A, 200A, 600A.
Peak /Data Hold.
Frequency Count /Diode Check.
Continuity Buzzer.
Low Battery Indication.

AC+DC 1200KW
DC/AC 2000A & ANALOG OUTPUT
Cable F 55mm
True RMS
Temperature ( ℃ or ℉ )
0.1 ℃ / ℉ Resolution

DC/AC 2000A
Cable f 55mm, Bus Bar 72mm(D) x 22mm(W)
True RMS (2000)
Average Sensing (2003)
DCA One Touch Zero
Auto Range A, V, W
Continuity
Max/Min/Hold
Relative Measurement

High Resolution DC 1mA, AC 0.1mA
Connect to an Oscilloscopes to observe Current Waceform
Connect to Chart Recorder/Datalogger/ DMM to Record Current Data

Accurate digital clamp meter for Current measurement: AC current: 0 ~ 30A (True RMS) DC current: 0 ~ 40A
Accurate digital clamp meter for Voltage measurement: AC voltage: 0 ~ 400V (True RMS) DC voltage: 0 ~ 400V
AC 0.1mA, DC 1mA high resolution
One touch zero for DCA adjustment
23 mm diameter jaw
Large 3 3/4 digits LCD
Fast bargraph display (30 times/sec.) for transient observation
Max/Min and Data Hold functions
Auto power off
Easy single rotary switch for any function selection

High Resolution DC 10mA, AC 1mA
True RMS
Non-contact Current Frequency Measurement

Accurate and High Resolution
23 mm Conductor Diameter
One Touch Zero

10 m A Ultra High Resolution
Large Conductor Diameter (30mm)
ACA 5 Ranges (40mA, 400mA, 4A, 40A, 100A

10 mA high resolution on 40A DC/AC range
Temperature (℃ or ℉) and Capacitance
One touch zero for DCA adjustment
Auto-range for V, A, Ω, F, and temperature
23 mm diameter jaw
Auto-power-off (15 minutes)
Fast bargraph display (30 times/sec.) for transient observation
Continuity and frequency measurements
Max/Min and Data Hold functions
600V overload protection for ohm measurement
Ideal for works in crowded switch box or cable areas

High Resolution DC/AC 10mA
23 mm Large Jaw Diameter
One Touch Zero for DCA adjustment